OP
Condobloke
Well-Known Member
It's out of the tower at the moment.....I will whack it back in, a couple of hours from now.
Stay tuned.
Stay tuned.
Locked SSD
- Thread starter Condobloke
- Start date
OP
Condobloke
Well-Known Member
reinstalled it
Pis from Computer, Disks, and then from GSmartControl
The warning when I start the pc is : Warning: The HDD is locked. & Please Enter HDD master password & The HDD is locked. please enter HDD user Password.
I am asked for password etc 3 or 4 times.....then the pc proceeds to boot (to my main drive....NVMe m2)
Has all this happened because I put the ssd into a HP laptop ??
OUTPUT
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-97-generic] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Samsung based SSDs
Device Model: Samsung SSD 750 EVO 120GB
Serial Number: S2SGNWAH216819V
LU WWN Device Id: 5 002538 d700d4466
Firmware Version: MAT01B6Q
User Capacity: 120,034,123,776 bytes [120 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
TRIM Command: Available
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon Mar 4 12:54:07 2024 AEDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: ENABLED, PW level HIGH, LOCKED [SEC4], PW ATTEMPTS EXCEEDED
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x53) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 64) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0
9 Power_On_Hours -O--CK 094 094 000 - 27195
12 Power_Cycle_Count -O--CK 097 097 000 - 2818
177 Wear_Leveling_Count PO--C- 041 041 000 - 296
179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0
181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0
182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0
183 Runtime_Bad_Block PO--C- 100 100 010 - 0
187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0
190 Airflow_Temperature_Cel -O--CK 067 050 000 - 33
195 ECC_Error_Rate -O-RC- 200 200 000 - 0
199 CRC_Error_Count -OSRCK 100 100 000 - 0
235 POR_Recovery_Count -O--C- 099 099 000 - 302
241 Total_LBAs_Written -O--CK 099 099 000 - 31103327798
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 1 Comprehensive SMART error log
0x03 GPL R/O 1 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x13 GPL R/O 1 SATA NCQ Send and Receive log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa1 SL VS 16 Device vendor specific log
0xa5 SL VS 16 Device vendor specific log
0xce SL VS 16 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 27195 -
# 2 Short offline Completed without error 00% 27191 -
# 3 Short offline Completed without error 00% 27189 -
# 4 Short offline Completed without error 00% 27183 -
# 5 Short offline Completed without error 00% 27168 -
# 6 Short offline Completed without error 00% 25293 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
255 0 65535 Read_scanning was never started
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Commands not supported if ATA Security is LOCKED
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 2 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC
Code:
brian@brian-desktop:~$ sudo smartctl -a /dev/sda1
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-97-generic] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
Smartctl open device: /dev/sda1 failed: No such device
brian@brian-desktop:~$Pis from Computer, Disks, and then from GSmartControl
The warning when I start the pc is : Warning: The HDD is locked. & Please Enter HDD master password & The HDD is locked. please enter HDD user Password.
I am asked for password etc 3 or 4 times.....then the pc proceeds to boot (to my main drive....NVMe m2)
Has all this happened because I put the ssd into a HP laptop ??
OUTPUT
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-97-generic] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Samsung based SSDs
Device Model: Samsung SSD 750 EVO 120GB
Serial Number: S2SGNWAH216819V
LU WWN Device Id: 5 002538 d700d4466
Firmware Version: MAT01B6Q
User Capacity: 120,034,123,776 bytes [120 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
TRIM Command: Available
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon Mar 4 12:54:07 2024 AEDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: ENABLED, PW level HIGH, LOCKED [SEC4], PW ATTEMPTS EXCEEDED
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x53) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 64) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0
9 Power_On_Hours -O--CK 094 094 000 - 27195
12 Power_Cycle_Count -O--CK 097 097 000 - 2818
177 Wear_Leveling_Count PO--C- 041 041 000 - 296
179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0
181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0
182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0
183 Runtime_Bad_Block PO--C- 100 100 010 - 0
187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0
190 Airflow_Temperature_Cel -O--CK 067 050 000 - 33
195 ECC_Error_Rate -O-RC- 200 200 000 - 0
199 CRC_Error_Count -OSRCK 100 100 000 - 0
235 POR_Recovery_Count -O--C- 099 099 000 - 302
241 Total_LBAs_Written -O--CK 099 099 000 - 31103327798
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 1 Comprehensive SMART error log
0x03 GPL R/O 1 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x13 GPL R/O 1 SATA NCQ Send and Receive log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa1 SL VS 16 Device vendor specific log
0xa5 SL VS 16 Device vendor specific log
0xce SL VS 16 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 27195 -
# 2 Short offline Completed without error 00% 27191 -
# 3 Short offline Completed without error 00% 27189 -
# 4 Short offline Completed without error 00% 27183 -
# 5 Short offline Completed without error 00% 27168 -
# 6 Short offline Completed without error 00% 25293 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
255 0 65535 Read_scanning was never started
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Commands not supported if ATA Security is LOCKED
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 2 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC
Attachments
OP
Condobloke
Well-Known Member
@osprey
@GatorsFan
@Brickwizard
@APTI
Do any of you guys know of an app that will RESET this drive?
I have seen AOEMI....windows only....surely Linux has an alternative?
I am told by the people at Samsung that a third party repairer can reset the drive...usually with 100% outcome
@GatorsFan
@Brickwizard
@APTI
Do any of you guys know of an app that will RESET this drive?
I have seen AOEMI....windows only....surely Linux has an alternative?
I am told by the people at Samsung that a third party repairer can reset the drive...usually with 100% outcome
Brickwizard
Well-Known Member
my mate said sudo hdparm --security-disable xxxx /dev/sd*
replace asterix with drive letter
he said it dosn't work with all makes of drive
replace asterix with drive letter
he said it dosn't work with all makes of drive
OP
Condobloke
Well-Known Member
Thanks @Brickwizard, I looked back through my terminal attempts, and have already tried that one, sadly with no success.
Thank your mate for me, please.
Thank your mate for me, please.
By reset do you mean the partition as in AOEMI Partition Manager does - if so you can use Gparted and do the same thing - simply delete the current partition and then create a new one
OP
Condobloke
Well-Known Member
Thanks @GatorsFan, the drive is not recognised by GParted.....nor by Gnome Disks
CaffeineAddict
Well-Known Member
See if you can erase it in UEFI, some UEFI's have this feature, my MSI has "secure erase" feature which let's me zero out drives.
Which mobo you have?
OP
Condobloke
Well-Known Member
I wish !!!!
My motherboard is an AsRock.....it has no such feature.
I will keep that MSI in mind for the next build.
Thanks @CaffeineAddict
CaffeineAddict
Well-Known Member
It's called "SSD Secure Erase Tool", see if you have this
See section 4.5 below:
This screenshot above shows no partition - hence is says "Unknown"
I'd try wiping the first few MB of the disk with dd and then create a new partition table and partition(s) with gparted.
Use e.g. sudo dd if=/dev/zero of=/dev/sdx bs=1M count=10
where "sdx" you need to replace x with the actual drive letter, from the screenshot it looks like sda
OP
Condobloke
Well-Known Member
Below is what the terminal looked like
This what GParted looked like after running the command
below is Disks after
Code:
brian@brian-desktop:~$ sudo dd if=/dev/zero of=/dev/sda bs=1M count=10
[sudo] password for brian:
10+0 records in
10+0 records out
10485760 bytes (10 MB, 10 MiB) copied, 0.00370532 s, 2.8 GB/s
brian@brian-desktop:~$This what GParted looked like after running the command
below is Disks after
CaffeineAddict
Well-Known Member
When the dd command finished you should have run:
sudo sync
OP
Condobloke
Well-Known Member
I attempted to format the ssd in Disks...
OP
Condobloke
Well-Known Member
Ok....will run it again and the sudo sync
CaffeineAddict
Well-Known Member
I think you can just run it without doing dd again because the disk is still attached, unless you rebooted system.
Before trying to format.... did you open the "Device" menu at the top of Gparted.... and first "Create Partition Table"? The dd command blows away the partition table, so that is needed before formatting.
OP
Condobloke
Well-Known Member
Yes, I did....but gparted doesn't recognise sda, ....so it immediately defaults to my main nvme drive....
CaffeineAddict
Well-Known Member
have you tried creating partition table and a new partition with
fdisk?What errors does fdisk report?
