iptables-extensions(8) iptables 1.4.21 iptables-extensions(8)
NAME
iptables-extensions — list of extensions in the standard iptables distribution
SYNOPSIS
ip6tables [-m name [module-options...]] [-j target-name [target-options...]
iptables [-m name [module-options...]] [-j target-name [target-options...]
MATCH EXTENSIONS
iptables can use extended packet matching modules with the -m or --match options, followed by the matching
module name; after these, various extra command line options become available, depending on the specific mod‐
ule. You can specify multiple extended match modules in one line, and you can use the -h or --help options
after the module has been specified to receive help specific to that module. The extended match modules are
evaluated in the order they are specified in the rule.
If the -p or --protocol was specified and if and only if an unknown option is encountered, iptables will try
load a match module of the same name as the protocol, to try making the option available.
addrtype
This module matches packets based on their address type. Address types are used within the kernel networking
stack and categorize addresses into various groups. The exact definition of that group depends on the spe‐
cific layer three protocol.
The following address types are possible:
UNSPEC an unspecified address (i.e. 0.0.0.0)
UNICAST
an unicast address
LOCAL a local address
BROADCAST
a broadcast address
ANYCAST
an anycast packet
MULTICAST
a multicast address
BLACKHOLE
a blackhole address
UNREACHABLE
an unreachable address
PROHIBIT
a prohibited address
THROW FIXME
NAT FIXME
XRESOLVE
The address type checking can be limited to the interface the packet is going out. This option is only
valid in the POSTROUTING, OUTPUT and FORWARD chains. It cannot be specified with the --limit-iface-in
option.
ah (IPv6-specific)
This module matches the parameters in Authentication header of IPsec packets.
[!] --ahspi spi[:spi]
Matches SPI.
[!] --ahlen length
Total length of this header in octets.
--ahres
Matches if the reserved field is filled with zero.
ah (IPv4-specific)
This module matches the SPIs in Authentication header of IPsec packets.
[!] --ahspi spi[:spi]
bpf
Match using Linux Socket Filter. Expects a BPF program in decimal format. This is the format generated by the
nfbpf_compile utility.
--bytecode code
Pass the BPF byte code format (described in the example below).
The code format is similar to the output of the tcpdump -ddd command: one line that stores the number of
instructions, followed by one line for each instruction. Instruction lines follow the pattern 'u16 u8 u8 u32'
in decimal notation. Fields encode the operation, jump offset if true, jump offset if false and generic mul‐
tiuse field 'K'. Comments are not supported.
For example, to read only packets matching 'ip proto 6', insert the following, without the comments or trail‐
ing whitespace:
4 # number of instructions
48 0 0 9 # load byte ip->proto
21 0 1 6 # jump equal IPPROTO_TCP
6 0 0 1 # return pass (non-zero)
6 0 0 0 # return fail (zero)
You can pass this filter to the bpf match with the following command:
iptables -A OUTPUT -m bpf --bytecode '4,48 0 0 9,21 0 1 6,6 0 0 1,6 0 0 0' -j ACCEPT
Or instead, you can invoke the nfbpf_compile utility.
iptables -A OUTPUT -m bpf --bytecode "`nfbpf_compile RAW 'ip proto 6'`" -j ACCEPT
You may want to learn more about BPF from FreeBSD's bpf(4) manpage.
cgroup
[!] --cgroup fwid
cluster
Allows you to deploy gateway and back-end load-sharing clusters without the need of load-balancers.
This match requires that all the nodes see the same packets. Thus, the cluster match decides if this node has
to handle a packet given the following options:
--cluster-total-nodes num
Set number of total nodes in cluster.
[!] --cluster-local-node num
Set the local node number ID.
[!] --cluster-local-nodemask mask
Set the local node number ID mask. You can use this option instead of --cluster-local-node.
--cluster-hash-seed value
Set seed value of the Jenkins hash.
Example:
iptables -A PREROUTING -t mangle -i eth1 -m cluster --cluster-total-nodes 2 --cluster-local-node 1
--cluster-hash-seed 0xdeadbeef -j MARK --set-mark 0xffff
iptables -A PREROUTING -t mangle -i eth2 -m cluster --cluster-total-nodes 2 --cluster-local-node 1
--cluster-hash-seed 0xdeadbeef -j MARK --set-mark 0xffff
iptables -A PREROUTING -t mangle -i eth1 -m mark ! --mark 0xffff -j DROP
iptables -A PREROUTING -t mangle -i eth2 -m mark ! --mark 0xffff -j DROP
And the following commands to make all nodes see the same packets:
ip maddr add 01:00:5e:00:01:01 dev eth1
ip maddr add 01:00:5e:00:01:02 dev eth2
arptables -A OUTPUT -o eth1 --h-length 6 -j mangle --mangle-mac-s 01:00:5e:00:01:01
arptables -A INPUT -i eth1 --h-length 6 --destination-mac 01:00:5e:00:01:01 -j mangle --mangle-mac-d
00:zz:yy:xx:5a:27
arptables -A OUTPUT -o eth2 --h-length 6 -j mangle --mangle-mac-s 01:00:5e:00:01:02
arptables -A INPUT -i eth2 --h-length 6 --destination-mac 01:00:5e:00:01:02 -j mangle --mangle-mac-d
00:zz:yy:xx:5a:27
NOTE: the arptables commands above use mainstream syntax. If you are using arptables-jf included in some Red‐
Hat, CentOS and Fedora versions, you will hit syntax errors. Therefore, you'll have to adapt these to the
arptables-jf syntax to get them working.
In the case of TCP connections, pickup facility has to be disabled to avoid marking TCP ACK packets coming in
the reply direction as valid.
echo 0 > /proc/sys/net/netfilter/nf_conntrack_tcp_loose
The counters are 64-bit and are thus not expected to overflow ;)
The primary use is to detect long-lived downloads and mark them to be scheduled using a lower priority band in
traffic control.
The transferred bytes per connection can also be viewed through `conntrack -L` and accessed via ctnetlink.
NOTE that for connections which have no accounting information, the match will always return false. The
"net.netfilter.nf_conntrack_acct" sysctl flag controls whether new connections will be byte/packet counted.
Existing connection flows will not be gaining/losing a/the accounting structure when be sysctl flag is
flipped.
[!] --connbytes from[:to]
match packets from a connection whose packets/bytes/average packet size is more than FROM and less than
TO bytes/packets. if TO is omitted only FROM check is done. "!" is used to match packets not falling in
the range.
--connbytes-dir {original|reply|both}
which packets to consider
--connbytes-mode {packets|bytes|avgpkt}
whether to check the amount of packets, number of bytes transferred or the average size (in bytes) of
all packets received so far. Note that when "both" is used together with "avgpkt", and data is going
(mainly) only in one direction (for example HTTP), the average packet size will be about half of the
actual data packets.
Example:
iptables .. -m connbytes --connbytes 10000:100000 --connbytes-dir both --connbytes-mode bytes ...
connlabel
Module matches or adds connlabels to a connection. connlabels are similar to connmarks, except labels are
bit-based; i.e. all labels may be attached to a flow at the same time. Up to 128 unique labels are currently
supported.
[!] --label name
matches if label name has been set on a connection. Instead of a name (which will be translated to a
number, see EXAMPLE below), a number may be used instead. Using a number always overrides connla‐
bel.conf.
--set if the label has not been set on the connection, set it. Note that setting a label can fail. This is
because the kernel allocates the conntrack label storage area when the connection is created, and it
only reserves the amount of memory required by the ruleset that exists at the time the connection is
created. In this case, the match will fail (or succeed, in case --label option was negated).
This match depends on libnetfilter_conntrack 1.0.4 or later. Label translation is done via the /etc/xta‐
bles/connlabel.conf configuration file.
Example:
0 eth0-in
1 eth0-out
2 ppp-in
3 ppp-out
--connlimit-mask prefix_length
Group hosts using the prefix length. For IPv4, this must be a number between (including) 0 and 32. For
IPv6, between 0 and 128. If not specified, the maximum prefix length for the applicable protocol is
used.
--connlimit-saddr
Apply the limit onto the source group. This is the default if --connlimit-daddr is not specified.
--connlimit-daddr
Apply the limit onto the destination group.
Examples:
# allow 2 telnet connections per client host
iptables -A INPUT -p tcp --syn --dport 23 -m connlimit --connlimit-above 2 -j REJECT
# you can also match the other way around:
iptables -A INPUT -p tcp --syn --dport 23 -m connlimit --connlimit-upto 2 -j ACCEPT
# limit the number of parallel HTTP requests to 16 per class C sized source network (24 bit netmask)
iptables -p tcp --syn --dport 80 -m connlimit --connlimit-above 16 --connlimit-mask 24 -j REJECT
# limit the number of parallel HTTP requests to 16 for the link local network
(ipv6) ip6tables -p tcp --syn --dport 80 -s fe80::/64 -m connlimit --connlimit-above 16
--connlimit-mask 64 -j REJECT
# Limit the number of connections to a particular host:
ip6tables -p tcp --syn --dport 49152:65535 -d 2001:db8::1 -m connlimit --connlimit-above 100 -j REJECT
connmark
This module matches the netfilter mark field associated with a connection (which can be set using the CONNMARK
target below).
[!] --mark value[/mask]
Matches packets in connections with the given mark value (if a mask is specified, this is logically
ANDed with the mark before the comparison).
conntrack
This module, when combined with connection tracking, allows access to the connection tracking state for this
packet/connection.
[!] --ctstate statelist
statelist is a comma separated list of the connection states to match. Possible states are listed
below.
[!] --ctproto l4proto
Layer-4 protocol to match (by number or name)
[!] --ctorigsrc address[/mask]
[!] --ctorigdst address[/mask]
[!] --ctreplsrc address[/mask]
ranges is only supported in kernel versions above 2.6.38.
[!] --ctstatus statelist
statuslist is a comma separated list of the connection statuses to match. Possible statuses are listed
below.
[!] --ctexpire time[:time]
Match remaining lifetime in seconds against given value or range of values (inclusive)
--ctdir {ORIGINAL|REPLY}
Match packets that are flowing in the specified direction. If this flag is not specified at all,
matches packets in both directions.
States for --ctstate:
INVALID
The packet is associated with no known connection.
NEW The packet has started a new connection or otherwise associated with a connection which has not seen
packets in both directions.
ESTABLISHED
The packet is associated with a connection which has seen packets in both directions.
RELATED
The packet is starting a new connection, but is associated with an existing connection, such as an FTP
data transfer or an ICMP error.
UNTRACKED
The packet is not tracked at all, which happens if you explicitly untrack it by using -j CT --notrack
in the raw table.
SNAT A virtual state, matching if the original source address differs from the reply destination.
DNAT A virtual state, matching if the original destination differs from the reply source.
Statuses for --ctstatus:
NONE None of the below.
EXPECTED
This is an expected connection (i.e. a conntrack helper set it up).
SEEN_REPLY
Conntrack has seen packets in both directions.
ASSURED
Conntrack entry should never be early-expired.
CONFIRMED
Connection is confirmed: originating packet has left box.
cpu
[!] --cpu number
[!] --source-port,--sport port[:port]
[!] --destination-port,--dport port[:port]
[!] --dccp-types mask
Match when the DCCP packet type is one of 'mask'. 'mask' is a comma-separated list of packet types.
Packet types are: REQUEST RESPONSE DATA ACK DATAACK CLOSEREQ CLOSE RESET SYNC SYNCACK INVALID.
[!] --dccp-option number
Match if DCCP option set.
devgroup
Match device group of a packets incoming/outgoing interface.
[!] --src-group name
Match device group of incoming device
[!] --dst-group name
Match device group of outgoing device
dscp
This module matches the 6 bit DSCP field within the TOS field in the IP header. DSCP has superseded TOS
within the IETF.
[!] --dscp value
Match against a numeric (decimal or hex) value [0-63].
[!] --dscp-class class
Match the DiffServ class. This value may be any of the BE, EF, AFxx or CSx classes. It will then be
converted into its according numeric value.
dst (IPv6-specific)
This module matches the parameters in Destination Options header
[!] --dst-len length
Total length of this header in octets.
--dst-opts type[:length][,type[:length]...]
numeric type of option and the length of the option data in octets.
ecn
This allows you to match the ECN bits of the IPv4/IPv6 and TCP header. ECN is the Explicit Congestion Notifi‐
cation mechanism as specified in RFC3168
[!] --ecn-tcp-cwr
This matches if the TCP ECN CWR (Congestion Window Received) bit is set.
[!] --ecn-tcp-ece
This matches if the TCP ECN ECE (ECN Echo) bit is set.
[!] --ecn-ip-ect num
This matches a particular IPv4/IPv6 ECT (ECN-Capable Transport). You have to specify a number between
`0' and `3'.
This module matches the parameters in Fragment header.
[!] --fragid id[:id]
Matches the given Identification or range of it.
[!] --fraglen length
This option cannot be used with kernel version 2.6.10 or later. The length of Fragment header is static
and this option doesn't make sense.
--fragres
Matches if the reserved fields are filled with zero.
--fragfirst
Matches on the first fragment.
--fragmore
Matches if there are more fragments.
--fraglast
Matches if this is the last fragment.
hashlimit
hashlimit uses hash buckets to express a rate limiting match (like the limit match) for a group of connections
using a single iptables rule. Grouping can be done per-hostgroup (source and/or destination address) and/or
per-port. It gives you the ability to express "N packets per time quantum per group" or "N bytes per seconds"
(see below for some examples).
A hash limit option (--hashlimit-upto, --hashlimit-above) and --hashlimit-name are required.
--hashlimit-upto amount[/second|/minute|/hour|/day]
Match if the rate is below or equal to amount/quantum. It is specified either as a number, with an
optional time quantum suffix (the default is 3/hour), or as amountb/second (number of bytes per sec‐
ond).
--hashlimit-above amount[/second|/minute|/hour|/day]
Match if the rate is above amount/quantum.
--hashlimit-burst amount
Maximum initial number of packets to match: this number gets recharged by one every time the limit
specified above is not reached, up to this number; the default is 5. When byte-based rate matching is
requested, this option specifies the amount of bytes that can exceed the given rate. This option
should be used with caution -- if the entry expires, the burst value is reset too.
--hashlimit-mode {srcip|srcport|dstip|dstport},...
A comma-separated list of objects to take into consideration. If no --hashlimit-mode option is given,
hashlimit acts like limit, but at the expensive of doing the hash housekeeping.
--hashlimit-srcmask prefix
When --hashlimit-mode srcip is used, all source addresses encountered will be grouped according to the
given prefix length and the so-created subnet will be subject to hashlimit. prefix must be between
(inclusive) 0 and 32. Note that --hashlimit-srcmask 0 is basically doing the same thing as not specify‐
ing srcip for --hashlimit-mode, but is technically more expensive.
--hashlimit-dstmask prefix
After how many milliseconds do hash entries expire.
--hashlimit-htable-gcinterval msec
How many milliseconds between garbage collection intervals.
Examples:
matching on source host
"1000 packets per second for every host in 192.168.0.0/16" => -s 192.168.0.0/16 --hashlimit-mode srcip
--hashlimit-upto 1000/sec
matching on source port
"100 packets per second for every service of 192.168.1.1" => -s 192.168.1.1 --hashlimit-mode srcport
--hashlimit-upto 100/sec
matching on subnet
"10000 packets per minute for every /28 subnet (groups of 8 addresses) in 10.0.0.0/8" => -s 10.0.0.0/8
--hashlimit-mask 28 --hashlimit-upto 10000/min
matching bytes per second
"flows exceeding 512kbyte/s" => --hashlimit-mode srcip,dstip,srcport,dstport --hashlimit-above 512kb/s
matching bytes per second
"hosts that exceed 512kbyte/s, but permit up to 1Megabytes without matching" --hashlimit-mode dstip
--hashlimit-above 512kb/s --hashlimit-burst 1mb
hbh (IPv6-specific)
This module matches the parameters in Hop-by-Hop Options header
[!] --hbh-len length
Total length of this header in octets.
--hbh-opts type[:length][,type[:length]...]
numeric type of option and the length of the option data in octets.
helper
This module matches packets related to a specific conntrack-helper.
[!] --helper string
Matches packets related to the specified conntrack-helper.
string can be "ftp" for packets related to a ftp-session on default port. For other ports append
-portnr to the value, ie. "ftp-2121".
Same rules apply for other conntrack-helpers.
hl (IPv6-specific)
This module matches the Hop Limit field in the IPv6 header.
[!] --hl-eq value
Matches if Hop Limit equals value.
--hl-lt value
Matches if Hop Limit is less than value.
icmp6 (IPv6-specific)
This extension can be used if `--protocol ipv6-icmp' or `--protocol icmpv6' is specified. It provides the fol‐
lowing option:
[!] --icmpv6-type type[/code]|typename
This allows specification of the ICMPv6 type, which can be a numeric ICMPv6 type, type and code, or one
of the ICMPv6 type names shown by the command
ip6tables -p ipv6-icmp -h
iprange
This matches on a given arbitrary range of IP addresses.
[!] --src-range from[-to]
Match source IP in the specified range.
[!] --dst-range from[-to]
Match destination IP in the specified range.
ipv6header (IPv6-specific)
This module matches IPv6 extension headers and/or upper layer header.
--soft Matches if the packet includes any of the headers specified with --header.
[!] --header header[,header...]
Matches the packet which EXACTLY includes all specified headers. The headers encapsulated with ESP
header are out of scope. Possible header types can be:
hop|hop-by-hop
Hop-by-Hop Options header
dst Destination Options header
route Routing header
frag Fragment header
auth Authentication header
esp Encapsulating Security Payload header
none No Next header which matches 59 in the 'Next Header field' of IPv6 header or any IPv6 extension headers
proto which matches any upper layer protocol header. A protocol name from /etc/protocols and numeric value
also allowed. The number 255 is equivalent to proto.
ipvs
Match IPVS connection properties.
[!] --ipvs
packet belongs to an IPVS connection
Any of the following options implies --ipvs (even negated)
[!] --vproto protocol
IPVS forwarding method used
[!] --vportctl port
VIP port of the controlling connection to match, e.g. 21 for FTP
length
This module matches the length of the layer-3 payload (e.g. layer-4 packet) of a packet against a specific
value or range of values.
[!] --length length[:length]
limit
This module matches at a limited rate using a token bucket filter. A rule using this extension will match
until this limit is reached. It can be used in combination with the LOG target to give limited logging, for
example.
xt_limit has no negation support - you will have to use -m hashlimit ! --hashlimit rate in this case whilst
omitting --hashlimit-mode.
--limit rate[/second|/minute|/hour|/day]
Maximum average matching rate: specified as a number, with an optional `/second', `/minute', `/hour',
or `/day' suffix; the default is 3/hour.
--limit-burst number
Maximum initial number of packets to match: this number gets recharged by one every time the limit
specified above is not reached, up to this number; the default is 5.
mac
[!] --mac-source address
Match source MAC address. It must be of the form XX:XX:XX:XX:XX:XX. Note that this only makes sense
for packets coming from an Ethernet device and entering the PREROUTING, FORWARD or INPUT chains.
mark
This module matches the netfilter mark field associated with a packet (which can be set using the MARK target
below).
[!] --mark value[/mask]
Matches packets with the given unsigned mark value (if a mask is specified, this is logically ANDed
with the mask before the comparison).
mh (IPv6-specific)
This extension is loaded if `--protocol ipv6-mh' or `--protocol mh' is specified. It provides the following
option:
[!] --mh-type type[:type]
This allows specification of the Mobility Header(MH) type, which can be a numeric MH type, type or one
of the MH type names shown by the command
ip6tables -p mh -h
multiport
This module matches a set of source or destination ports. Up to 15 ports can be specified. A port range
(port:port) counts as two ports. It can only be used in conjunction with one of the following protocols: tcp,
udp, udplite, dccp and sctp.
nfacct
The nfacct match provides the extended accounting infrastructure for iptables. You have to use this match
together with the standalone user-space utility nfacct(8)
The only option available for this match is the following:
--nfacct-name name
This allows you to specify the existing object name that will be use for accounting the traffic that
this rule-set is matching.
To use this extension, you have to create an accounting object:
nfacct add http-traffic
Then, you have to attach it to the accounting object via iptables:
iptables -I INPUT -p tcp --sport 80 -m nfacct --nfacct-name http-traffic
iptables -I OUTPUT -p tcp --dport 80 -m nfacct --nfacct-name http-traffic
Then, you can check for the amount of traffic that the rules match:
nfacct get http-traffic
{ pkts = 00000000000000000156, bytes = 00000000000000151786 } = http-traffic;
You can obtain nfacct(8) from http://www.netfilter.org or, alternatively, from the git.netfilter.org reposi‐
tory.
osf
The osf module does passive operating system fingerprinting. This modules compares some data (Window Size,
MSS, options and their order, TTL, DF, and others) from packets with the SYN bit set.
[!] --genre string
Match an operating system genre by using a passive fingerprinting.
--ttl level
Do additional TTL checks on the packet to determine the operating system. level can be one of the fol‐
lowing values:
· 0 - True IP address and fingerprint TTL comparison. This generally works for LANs.
· 1 - Check if the IP header's TTL is less than the fingerprint one. Works for globally-routable addresses.
· 2 - Do not compare the TTL at all.
--log level
Log determined genres into dmesg even if they do not match the desired one. level can be one of the fol‐
lowing values:
· 0 - Log all matched or unknown signatures
· 1 - Log only the first one
nfnl_osf -f /usr/share/xtables/pf.os -d
The fingerprint database can be downlaoded from http://www.openbsd.org/cgi-bin/cvsweb/src/etc/pf.os .
owner
This module attempts to match various characteristics of the packet creator, for locally generated packets.
This match is only valid in the OUTPUT and POSTROUTING chains. Forwarded packets do not have any socket asso‐
ciated with them. Packets from kernel threads do have a socket, but usually no owner.
[!] --uid-owner username
[!] --uid-owner userid[-userid]
Matches if the packet socket's file structure (if it has one) is owned by the given user. You may also
specify a numerical UID, or an UID range.
[!] --gid-owner groupname
[!] --gid-owner groupid[-groupid]
Matches if the packet socket's file structure is owned by the given group. You may also specify a
numerical GID, or a GID range.
[!] --socket-exists
Matches if the packet is associated with a socket.
physdev
This module matches on the bridge port input and output devices enslaved to a bridge device. This module is a
part of the infrastructure that enables a transparent bridging IP firewall and is only useful for kernel ver‐
sions above version 2.5.44.
[!] --physdev-in name
Name of a bridge port via which a packet is received (only for packets entering the INPUT, FORWARD and
PREROUTING chains). If the interface name ends in a "+", then any interface which begins with this name
will match. If the packet didn't arrive through a bridge device, this packet won't match this option,
unless '!' is used.
[!] --physdev-out name
Name of a bridge port via which a packet is going to be sent (for packets entering the FORWARD, OUTPUT
and POSTROUTING chains). If the interface name ends in a "+", then any interface which begins with
this name will match. Note that in the nat and mangle OUTPUT chains one cannot match on the bridge out‐
put port, however one can in the filter OUTPUT chain. If the packet won't leave by a bridge device or
if it is yet unknown what the output device will be, then the packet won't match this option, unless
'!' is used.
[!] --physdev-is-in
Matches if the packet has entered through a bridge interface.
[!] --physdev-is-out
Matches if the packet will leave through a bridge interface.
[!] --physdev-is-bridged
Matches if the packet is being bridged and therefore is not being routed. This is only useful in the
FORWARD and POSTROUTING chains.
--pol {none|ipsec}
Matches if the packet is subject to IPsec processing. --pol none cannot be combined with --strict.
--strict
Selects whether to match the exact policy or match if any rule of the policy matches the given policy.
For each policy element that is to be described, one can use one or more of the following options. When
--strict is in effect, at least one must be used per element.
[!] --reqid id
Matches the reqid of the policy rule. The reqid can be specified with setkey(8) using unique:id as
level.
[!] --spi spi
Matches the SPI of the SA.
[!] --proto {ah|esp|ipcomp}
Matches the encapsulation protocol.
[!] --mode {tunnel|transport}
Matches the encapsulation mode.
[!] --tunnel-src addr[/mask]
Matches the source end-point address of a tunnel mode SA. Only valid with --mode tunnel.
[!] --tunnel-dst addr[/mask]
Matches the destination end-point address of a tunnel mode SA. Only valid with --mode tunnel.
--next Start the next element in the policy specification. Can only be used with --strict.
quota
Implements network quotas by decrementing a byte counter with each packet. The condition matches until the
byte counter reaches zero. Behavior is reversed with negation (i.e. the condition does not match until the
byte counter reaches zero).
[!] --quota bytes
The quota in bytes.
rateest
The rate estimator can match on estimated rates as collected by the RATEEST target. It supports matching on
absolute bps/pps values, comparing two rate estimators and matching on the difference between two rate estima‐
tors.
For a better understanding of the available options, these are all possible combinations:
· rateest operator rateest-bps
· rateest operator rateest-pps
· (rateest minus rateest-bps1) operator rateest-bps2
· (rateest minus rateest-pps1) operator rateest-pps2
rateest#_bps)" is used.
[!] --rateest-lt
Match if rate is less than given rate/estimator.
[!] --rateest-gt
Match if rate is greater than given rate/estimator.
[!] --rateest-eq
Match if rate is equal to given rate/estimator.
In the so-called "absolute mode", only one rate estimator is used and compared against a static value, while
in "relative mode", two rate estimators are compared against another.
--rateest name
Name of the one rate estimator for absolute mode.
--rateest1 name
--rateest2 name
The names of the two rate estimators for relative mode.
--rateest-bps [value]
--rateest-pps [value]
--rateest-bps1 [value]
--rateest-bps2 [value]
--rateest-pps1 [value]
--rateest-pps2 [value]
Compare the estimator(s) by bytes or packets per second, and compare against the chosen value. See the
above bullet list for which option is to be used in which case. A unit suffix may be used - available
ones are: bit, [kmgt]bit, [KMGT]ibit, Bps, [KMGT]Bps, [KMGT]iBps.
Example: This is what can be used to route outgoing data connections from an FTP server over two lines based
on the available bandwidth at the time the data connection was started:
# Estimate outgoing rates
iptables -t mangle -A POSTROUTING -o eth0 -j RATEEST --rateest-name eth0 --rateest-interval 250ms
--rateest-ewma 0.5s
iptables -t mangle -A POSTROUTING -o ppp0 -j RATEEST --rateest-name ppp0 --rateest-interval 250ms
--rateest-ewma 0.5s
# Mark based on available bandwidth
iptables -t mangle -A balance -m conntrack --ctstate NEW -m helper --helper ftp -m rateest --rateest-delta
--rateest1 eth0 --rateest-bps1 2.5mbit --rateest-gt --rateest2 ppp0 --rateest-bps2 2mbit -j CONNMARK
--set-mark 1
/etc/iproute2/rt_realms (mask can not be used in that case).
recent
Allows you to dynamically create a list of IP addresses and then match against that list in a few different
ways.
For example, you can create a "badguy" list out of people attempting to connect to port 139 on your firewall
and then DROP all future packets from them without considering them.
--set, --rcheck, --update and --remove are mutually exclusive.
--name name
Specify the list to use for the commands. If no name is given then DEFAULT will be used.
[!] --set
This will add the source address of the packet to the list. If the source address is already in the
list, this will update the existing entry. This will always return success (or failure if ! is passed
in).
--rsource
Match/save the source address of each packet in the recent list table. This is the default.
--rdest
Match/save the destination address of each packet in the recent list table.
--mask netmask
Netmask that will be applied to this recent list.
[!] --rcheck
Check if the source address of the packet is currently in the list.
[!] --update
Like --rcheck, except it will update the "last seen" timestamp if it matches.
[!] --remove
Check if the source address of the packet is currently in the list and if so that address will be
removed from the list and the rule will return true. If the address is not found, false is returned.
--seconds seconds
This option must be used in conjunction with one of --rcheck or --update. When used, this will narrow
the match to only happen when the address is in the list and was seen within the last given number of
seconds.
--reap This option can only be used in conjunction with --seconds. When used, this will cause entries older
than the last given number of seconds to be purged.
--hitcount hits
This option must be used in conjunction with one of --rcheck or --update. When used, this will narrow
the match to only happen when the address is in the list and packets had been received greater than or
equal to the given value. This option may be used along with --seconds to create an even narrower match
requiring a certain number of hits within a specific time frame. The maximum value for the hitcount
parameter is given by the "ip_pkt_list_tot" parameter of the xt_recent kernel module. Exceeding this
value on the command line will cause the rule to be rejected.
/proc/net/xt_recent/* are the current lists of addresses and information about each entry of each list.
Each file in /proc/net/xt_recent/ can be read from to see the current list or written two using the following
commands to modify the list:
echo +addr >/proc/net/xt_recent/DEFAULT
to add addr to the DEFAULT list
echo -addr >/proc/net/xt_recent/DEFAULT
to remove addr from the DEFAULT list
echo / >/proc/net/xt_recent/DEFAULT
to flush the DEFAULT list (remove all entries).
The module itself accepts parameters, defaults shown:
ip_list_tot=100
Number of addresses remembered per table.
ip_pkt_list_tot=20
Number of packets per address remembered.
ip_list_hash_size=0
Hash table size. 0 means to calculate it based on ip_list_tot, default: 512.
ip_list_perms=0644
Permissions for /proc/net/xt_recent/* files.
ip_list_uid=0
Numerical UID for ownership of /proc/net/xt_recent/* files.
ip_list_gid=0
Numerical GID for ownership of /proc/net/xt_recent/* files.
rpfilter
Performs a reverse path filter test on a packet. If a reply to the packet would be sent via the same inter‐
face that the packet arrived on, the packet will match. Note that, unlike the in-kernel rp_filter, packets
protected by IPSec are not treated specially. Combine this match with the policy match if you want this.
Also, packets arriving via the loopback interface are always permitted. This match can only be used in the
PREROUTING chain of the raw or mangle table.
--loose
Used to specifiy that the reverse path filter test should match even if the selected output device is
not the expected one.
--validmark
Also use the packets' nfmark value when performing the reverse path route lookup.
--accept-local
This will permit packets arriving from the network with a source address that is also assigned to the
local machine.
--invert
This will invert the sense of the match. Instead of matching packets that passed the reverse path fil‐
iptables -t raw -A PREROUTING -j RPFILTER
Example to drop failed packets, without logging:
iptables -t raw -A RPFILTER -m rpfilter --invert -j DROP
rt (IPv6-specific)
Match on IPv6 routing header
[!] --rt-type type
Match the type (numeric).
[!] --rt-segsleft num[:num]
Match the `segments left' field (range).
[!] --rt-len length
Match the length of this header.
--rt-0-res
Match the reserved field, too (type=0)
--rt-0-addrs addr[,addr...]
Match type=0 addresses (list).
--rt-0-not-strict
List of type=0 addresses is not a strict list.
sctp
[!] --source-port,--sport port[:port]
[!] --destination-port,--dport port[:port]
[!] --chunk-types {all|any|only} chunktype[:flags] [...]
The flag letter in upper case indicates that the flag is to match if set, in the lower case indicates
to match if unset.
Chunk types: DATA INIT INIT_ACK SACK HEARTBEAT HEARTBEAT_ACK ABORT SHUTDOWN SHUTDOWN_ACK ERROR
COOKIE_ECHO COOKIE_ACK ECN_ECNE ECN_CWR SHUTDOWN_COMPLETE ASCONF ASCONF_ACK FORWARD_TSN
chunk type available flags
DATA I U B E i u b e
ABORT T t
SHUTDOWN_COMPLETE T t
(lowercase means flag should be "off", uppercase means "on")
Examples:
iptables -A INPUT -p sctp --dport 80 -j DROP
iptables -A INPUT -p sctp --chunk-types any DATA,INIT -j DROP
iptables -A INPUT -p sctp --chunk-types any DATA:Be -j ACCEPT
specified set.
--return-nomatch
If the --return-nomatch option is specified and the set type supports the nomatch flag, then the match‐
ing is reversed: a match with an element flagged with nomatch returns true, while a match with a plain
element returns false.
! --update-counters
If the --update-counters flag is negated, then the packet and byte counters of the matching element in
the set won't be updated. Default the packet and byte counters are updated.
! --update-subcounters
If the --update-subcounters flag is negated, then the packet and byte counters of the matching element
in the member set of a list type of set won't be updated. Default the packet and byte counters are
updated.
[!] --packets-eq value
If the packet is matched an element in the set, match only if the packet counter of the element matches
the given value too.
--packets-lt value
If the packet is matched an element in the set, match only if the packet counter of the element is less
than the given value as well.
--packets-gt value
If the packet is matched an element in the set, match only if the packet counter of the element is
greater than the given value as well.
[!] -bytes-eq value
If the packet is matched an element in the set, match only if the byte counter of the element matches
the given value too.
--bytes-lt value
If the packet is matched an element in the set, match only if the byte counter of the element is less
than the given value as well.
--bytes-gt value
If the packet is matched an element in the set, match only if the byte counter of the element is
greater than the given value as well.
The packet and byte counters related options and flags are ignored when the set was defined without counter
support.
The option --match-set can be replaced by --set if that does not clash with an option of other extensions.
Use of -m set requires that ipset kernel support is provided, which, for standard kernels, is the case since
Linux 2.6.39.
socket
This matches if an open TCP/UDP socket can be found by doing a socket lookup on the packet. It matches if
there is an established or non-zero bound listening socket (possibly with a non-local address). The lookup is
performed using the packet tuple of TCP/UDP packets, or the original TCP/UDP header embedded in an ICMP/ICPMv6
error packet.
-t mangle -A PREROUTING -m socket --transparent -j MARK --set-mark 1
state
The "state" extension is a subset of the "conntrack" module. "state" allows access to the connection tracking
state for this packet.
[!] --state state
Where state is a comma separated list of the connection states to match. Only a subset of the states
unterstood by "conntrack" are recognized: INVALID, ESTABLISHED, NEW, RELATED or UNTRACKED. For their
description, see the "conntrack" heading in this manpage.
statistic
This module matches packets based on some statistic condition. It supports two distinct modes settable with
the --mode option.
Supported options:
--mode mode
Set the matching mode of the matching rule, supported modes are random and nth.
[!] --probability p
Set the probability for a packet to be randomly matched. It only works with the random mode. p must be
within 0.0 and 1.0. The supported granularity is in 1/2147483648th increments.
[!] --every n
Match one packet every nth packet. It works only with the nth mode (see also the --packet option).
--packet p
Set the initial counter value (0 <= p <= n-1, default 0) for the nth mode.
string
This modules matches a given string by using some pattern matching strategy. It requires a linux kernel >=
2.6.14.
--algo {bm|kmp}
Select the pattern matching strategy. (bm = Boyer-Moore, kmp = Knuth-Pratt-Morris)
--from offset
Set the offset from which it starts looking for any matching. If not passed, default is 0.
--to offset
Set the offset up to which should be scanned. That is, byte offset-1 (counting from 0) is the last one
that is scanned. If not passed, default is the packet size.
[!] --string pattern
Matches the given pattern.
[!] --hex-string pattern
Matches the given pattern in hex notation.
Examples:
# The string pattern can be used for simple text characters.
iptables -A INPUT -p tcp --dport 80 -m string --algo bm --string 'GET /index.html' -j LOG
they will be swapped. The flag --sport is a convenient alias for this option.
[!] --destination-port,--dport port[:port]
Destination port or port range specification. The flag --dport is a convenient alias for this option.
[!] --tcp-flags mask comp
Match when the TCP flags are as specified. The first argument mask is the flags which we should exam‐
ine, written as a comma-separated list, and the second argument comp is a comma-separated list of flags
which must be set. Flags are: SYN ACK FIN RST URG PSH ALL NONE. Hence the command
iptables -A FORWARD -p tcp --tcp-flags SYN,ACK,FIN,RST SYN
will only match packets with the SYN flag set, and the ACK, FIN and RST flags unset.
[!] --syn
Only match TCP packets with the SYN bit set and the ACK,RST and FIN bits cleared. Such packets are
used to request TCP connection initiation; for example, blocking such packets coming in an interface
will prevent incoming TCP connections, but outgoing TCP connections will be unaffected. It is equiva‐
lent to --tcp-flags SYN,RST,ACK,FIN SYN. If the "!" flag precedes the "--syn", the sense of the option
is inverted.
[!] --tcp-option number
Match if TCP option set.
tcpmss
This matches the TCP MSS (maximum segment size) field of the TCP header. You can only use this on TCP SYN or
SYN/ACK packets, since the MSS is only negotiated during the TCP handshake at connection startup time.
[!] --mss value[:value]
Match a given TCP MSS value or range.
time
This matches if the packet arrival time/date is within a given range. All options are optional, but are ANDed
when specified. All times are interpreted as UTC by default.
--datestart YYYY[-MM[-DD[Thh[:mm[:ss]]]]]
--datestop YYYY[-MM[-DD[Thh[:mm[:ss]]]]]
Only match during the given time, which must be in ISO 8601 "T" notation. The possible time range is
1970-01-01T00:00:00 to 2038-01-19T04:17:07.
If --datestart or --datestop are not specified, it will default to 1970-01-01 and 2038-01-19, respec‐
tively.
--timestart hh:mm[:ss]
--timestop hh:mm[:ss]
Only match during the given daytime. The possible time range is 00:00:00 to 23:59:59. Leading zeroes
are allowed (e.g. "06:03") and correctly interpreted as base-10.
[!] --monthdays day[,day...]
Only match on the given days of the month. Possible values are 1 to 31. Note that specifying 31 will of
course not match on months which do not have a 31st day; the same goes for 28- or 29-day February.
[!] --weekdays day[,day...]
Only match on the given weekdays. Possible values are Mon, Tue, Wed, Thu, Fri, Sat, Sun, or values from
system time and timezone to the kernel once it has the information.
Local time is a feature on top of the (timezone independent) system time. Each process has its own idea of
local time, specified via the TZ environment variable. The kernel also has its own timezone offset variable.
The TZ userspace environment variable specifies how the UTC-based system time is displayed, e.g. when you run
date(1), or what you see on your desktop clock. The TZ string may resolve to different offsets at different
dates, which is what enables the automatic time-jumping in userspace. when DST changes. The kernel's timezone
offset variable is used when it has to convert between non-UTC sources, such as FAT filesystems, to UTC (since
the latter is what the rest of the system uses).
The caveat with the kernel timezone is that Linux distributions may ignore to set the kernel timezone, and
instead only set the system time. Even if a particular distribution does set the timezone at boot, it is usu‐
ally does not keep the kernel timezone offset - which is what changes on DST - up to date. ntpd will not
touch the kernel timezone, so running it will not resolve the issue. As such, one may encounter a timezone
that is always +0000, or one that is wrong half of the time of the year. As such, using --kerneltz is highly
discouraged.
EXAMPLES. To match on weekends, use:
-m time --weekdays Sa,Su
Or, to match (once) on a national holiday block:
-m time --datestart 2007-12-24 --datestop 2007-12-27
Since the stop time is actually inclusive, you would need the following stop time to not match the first sec‐
ond of the new day:
-m time --datestart 2007-01-01T17:00 --datestop 2007-01-01T23:59:59
During lunch hour:
-m time --timestart 12:30 --timestop 13:30
The fourth Friday in the month:
-m time --weekdays Fr --monthdays 22,23,24,25,26,27,28
(Note that this exploits a certain mathematical property. It is not possible to say "fourth Thursday OR fourth
Friday" in one rule. It is possible with multiple rules, though.)
Matching across days might not do what is expected. For instance,
-m time --weekdays Mo --timestart 23:00 --timestop 01:00 Will match Monday, for one hour from midnight
to 1 a.m., and then again for another hour from 23:00 onwards. If this is unwanted, e.g. if you would
like 'match for two hours from Montay 23:00 onwards' you need to also specify the --contiguous option
in the example above.
tos
This module matches the 8-bit Type of Service field in the IPv4 header (i.e. including the "Precedence" bits)
or the (also 8-bit) Priority field in the IPv6 header.
[!] --tos value[/mask]
Matches packets with the given TOS mark value. If a mask is specified, it is logically ANDed with the
--ttl-gt ttl
Matches if TTL is greater than the given TTL value.
--ttl-lt ttl
Matches if TTL is less than the given TTL value.
u32
U32 tests whether quantities of up to 4 bytes extracted from a packet have specified values. The specification
of what to extract is general enough to find data at given offsets from tcp headers or payloads.
[!] --u32 tests
The argument amounts to a program in a small language described below.
tests := location "=" value | tests "&&" location "=" value
value := range | value "," range
range := number | number ":" number
a single number, n, is interpreted the same as n:n. n:m is interpreted as the range of numbers >=n and <=m.
location := number | location operator number
operator := "&" | "<<" | ">>" | "@"
The operators &, <<, >> and && mean the same as in C. The = is really a set membership operator and the value
syntax describes a set. The @ operator is what allows moving to the next header and is described further
below.
There are currently some artificial implementation limits on the size of the tests:
* no more than 10 of "=" (and 9 "&&"s) in the u32 argument
* no more than 10 ranges (and 9 commas) per value
* no more than 10 numbers (and 9 operators) per location
To describe the meaning of location, imagine the following machine that interprets it. There are three regis‐
ters:
A is of type char *, initially the address of the IP header
B and C are unsigned 32 bit integers, initially zero
The instructions are:
number B = number;
C = (*(A+B)<<24) + (*(A+B+1)<<16) + (*(A+B+2)<<8) + *(A+B+3)
&number C = C & number
<< number C = C << number
match IP packets with total length >= 256
The IP header contains a total length field in bytes 2-3.
--u32 "0 & 0xFFFF = 0x100:0xFFFF"
read bytes 0-3
AND that with 0xFFFF (giving bytes 2-3), and test whether that is in the range [0x100:0xFFFF]
Example: (more realistic, hence more complicated)
match ICMP packets with icmp type 0
First test that it is an ICMP packet, true iff byte 9 (protocol) = 1
--u32 "6 & 0xFF = 1 && ...
read bytes 6-9, use & to throw away bytes 6-8 and compare the result to 1. Next test that it is not a
fragment. (If so, it might be part of such a packet but we cannot always tell.) N.B.: This test is gen‐
erally needed if you want to match anything beyond the IP header. The last 6 bits of byte 6 and all of
byte 7 are 0 iff this is a complete packet (not a fragment). Alternatively, you can allow first frag‐
ments by only testing the last 5 bits of byte 6.
... 4 & 0x3FFF = 0 && ...
Last test: the first byte past the IP header (the type) is 0. This is where we have to use the @syntax.
The length of the IP header (IHL) in 32 bit words is stored in the right half of byte 0 of the IP
header itself.
... 0 >> 22 & 0x3C @ 0 >> 24 = 0"
The first 0 means read bytes 0-3, >>22 means shift that 22 bits to the right. Shifting 24 bits would
give the first byte, so only 22 bits is four times that plus a few more bits. &3C then eliminates the
two extra bits on the right and the first four bits of the first byte. For instance, if IHL=5, then the
IP header is 20 (4 x 5) bytes long. In this case, bytes 0-1 are (in binary) xxxx0101 yyzzzzzz, >>22
gives the 10 bit value xxxx0101yy and &3C gives 010100. @ means to use this number as a new offset into
the packet, and read four bytes starting from there. This is the first 4 bytes of the ICMP payload, of
which byte 0 is the ICMP type. Therefore, we simply shift the value 24 to the right to throw out all
but the first byte and compare the result with 0.
Example:
TCP payload bytes 8-12 is any of 1, 2, 5 or 8
First we test that the packet is a tcp packet (similar to ICMP).
--u32 "6 & 0xFF = 6 && ...
Next, test that it is not a fragment (same as above).
... 0 >> 22 & 0x3C @ 12 >> 26 & 0x3C @ 8 = 1,2,5,8"
[!] --destination-port,--dport port[:port]
Destination port or port range specification. See the description of the --destination-port option of
the TCP extension for details.
unclean (IPv4-specific)
This module takes no options, but attempts to match packets which seem malformed or unusual. This is regarded
as experimental.
TARGET EXTENSIONS
iptables can use extended target modules: the following are included in the standard distribution.
AUDIT
This target allows to create audit records for packets hitting the target. It can be used to record accepted,
dropped, and rejected packets. See auditd(8) for additional details.
--type {accept|drop|reject}
Set type of audit record.
Example:
iptables -N AUDIT_DROP
iptables -A AUDIT_DROP -j AUDIT --type drop
iptables -A AUDIT_DROP -j DROP
CHECKSUM
This target allows to selectively work around broken/old applications. It can only be used in the mangle ta‐
ble.
--checksum-fill
Compute and fill in the checksum in a packet that lacks a checksum. This is particularly useful, if
you need to work around old applications such as dhcp clients, that do not work well with checksum off‐
loads, but don't want to disable checksum offload in your device.
CLASSIFY
This module allows you to set the skb->priority value (and thus classify the packet into a specific CBQ
class).
--set-class major:minor
Set the major and minor class value. The values are always interpreted as hexadecimal even if no 0x
prefix is given.
CLUSTERIP (IPv4-specific)
This module allows you to configure a simple cluster of nodes that share a certain IP and MAC address without
an explicit load balancer in front of them. Connections are statically distributed between the nodes in this
cluster.
--new Create a new ClusterIP. You always have to set this on the first rule for a given ClusterIP.
--hashmode mode
Specify the hashing mode. Has to be one of sourceip, sourceip-sourceport, sourceip-sourceport-dest‐
port.
CONNMARK
This module sets the netfilter mark value associated with a connection. The mark is 32 bits wide.
--set-xmark value[/mask]
Zero out the bits given by mask and XOR value into the ctmark.
--save-mark [--nfmask nfmask] [--ctmask ctmask]
Copy the packet mark (nfmark) to the connection mark (ctmark) using the given masks. The new nfmark
value is determined as follows:
ctmark = (ctmark & ~ctmask) ^ (nfmark & nfmask)
i.e. ctmask defines what bits to clear and nfmask what bits of the nfmark to XOR into the ctmark.
ctmask and nfmask default to 0xFFFFFFFF.
--restore-mark [--nfmask nfmask] [--ctmask ctmask]
Copy the connection mark (ctmark) to the packet mark (nfmark) using the given masks. The new ctmark
value is determined as follows:
nfmark = (nfmark & ~nfmask) ^ (ctmark & ctmask);
i.e. nfmask defines what bits to clear and ctmask what bits of the ctmark to XOR into the nfmark.
ctmask and nfmask default to 0xFFFFFFFF.
--restore-mark is only valid in the mangle table.
The following mnemonics are available for --set-xmark:
--and-mark bits
Binary AND the ctmark with bits. (Mnemonic for --set-xmark 0/invbits, where invbits is the binary nega‐
tion of bits.)
--or-mark bits
Binary OR the ctmark with bits. (Mnemonic for --set-xmark bits/bits.)
--xor-mark bits
Binary XOR the ctmark with bits. (Mnemonic for --set-xmark bits/0.)
--set-mark value[/mask]
Set the connection mark. If a mask is specified then only those bits set in the mask are modified.
--save-mark [--mask mask]
Copy the nfmark to the ctmark. If a mask is specified, only those bits are copied.
--restore-mark [--mask mask]
Copy the ctmark to the nfmark. If a mask is specified, only those bits are copied. This is only valid
in the mangle table.
CONNSECMARK
This module copies security markings from packets to connections (if unlabeled), and from connections back to
packets (also only if unlabeled). Typically used in conjunction with SECMARK, it is valid in the security ta‐
ble (for backwards compatibility with older kernels, it is also valid in the mangle table).
--notrack
Disables connection tracking for this packet.
--helper name
Use the helper identified by name for the connection. This is more flexible than loading the conntrack
helper modules with preset ports.
--ctevents event[,...]
Only generate the specified conntrack events for this connection. Possible event types are: new,
related, destroy, reply, assured, protoinfo, helper, mark (this refers to the ctmark, not nfmark), nat‐
seqinfo, secmark (ctsecmark).
--expevents event[,...]
Only generate the specified expectation events for this connection. Possible event types are: new.
--zone id
Assign this packet to zone id and only have lookups done in that zone. By default, packets have zone
0.
--timeout name
Use the timeout policy identified by name for the connection. This is provides more flexible timeout
policy definition than global timeout values available at /proc/sys/net/netfilter/nf_conntrack_*_time‐
out_*.
DNAT
This target is only valid in the nat table, in the PREROUTING and OUTPUT chains, and user-defined chains which
are only called from those chains. It specifies that the destination address of the packet should be modified
(and all future packets in this connection will also be mangled), and rules should cease being examined. It
takes the following options:
--to-destination [ipaddr[-ipaddr]][:port[-port]]
which can specify a single new destination IP address, an inclusive range of IP addresses. Optionally a
port range, if the rule also specifies one of the following protocols: tcp, udp, dccp or sctp. If no
port range is specified, then the destination port will never be modified. If no IP address is speci‐
fied then only the destination port will be modified. In Kernels up to 2.6.10 you can add several
--to-destination options. For those kernels, if you specify more than one destination address, either
via an address range or multiple --to-destination options, a simple round-robin (one after another in
cycle) load balancing takes place between these addresses. Later Kernels (>= 2.6.11-rc1) don't have
the ability to NAT to multiple ranges anymore.
--random
If option --random is used then port mapping will be randomized (kernel >= 2.6.22).
--persistent
Gives a client the same source-/destination-address for each connection. This supersedes the SAME tar‐
get. Support for persistent mappings is available from 2.6.29-rc2.
IPv6 support available since Linux kernels >= 3.7.
DNPT (IPv6-specific)
Provides stateless destination IPv6-to-IPv6 Network Prefix Translation (as described by RFC 6296).
You have to use this target in the mangle table, not in the nat table. It takes the following options:
2001:e20:2000:40f::/64 --dst-pfx fd00::/64
You may need to enable IPv6 neighbor proxy:
sysctl -w net.ipv6.conf.all.proxy_ndp=1
You also have to use the NOTRACK target to disable connection tracking for translated flows.
DSCP
This target allows to alter the value of the DSCP bits within the TOS header of the IPv4 packet. As this
manipulates a packet, it can only be used in the mangle table.
--set-dscp value
Set the DSCP field to a numerical value (can be decimal or hex)
--set-dscp-class class
Set the DSCP field to a DiffServ class.
ECN (IPv4-specific)
This target allows to selectively work around known ECN blackholes. It can only be used in the mangle table.
--ecn-tcp-remove
Remove all ECN bits from the TCP header. Of course, it can only be used in conjunction with -p tcp.
HL (IPv6-specific)
This is used to modify the Hop Limit field in IPv6 header. The Hop Limit field is similar to what is known as
TTL value in IPv4. Setting or incrementing the Hop Limit field can potentially be very dangerous, so it
should be avoided at any cost. This target is only valid in mangle table.
Don't ever set or increment the value on packets that leave your local network!
--hl-set value
Set the Hop Limit to `value'.
--hl-dec value
Decrement the Hop Limit `value' times.
--hl-inc value
Increment the Hop Limit `value' times.
HMARK
Like MARK, i.e. set the fwmark, but the mark is calculated from hashing packet selector at choice. You have
also to specify the mark range and, optionally, the offset to start from. ICMP error messages are inspected
and used to calculate the hashing.
Existing options are:
--hmark-tuple tuple
Possible tuple members are: src meaning source address (IPv4, IPv6 address), dst meaning destination
address (IPv4, IPv6 address), sport meaning source port (TCP, UDP, UDPlite, SCTP, DCCP), dport meaning
destination port (TCP, UDP, UDPlite, SCTP, DCCP), spi meaning Security Parameter Index (AH, ESP), and
ct meaning the usage of the conntrack tuple instead of the packet selectors.
--hmark-mod value (must be > 0)
The destination address mask in CIDR notation.
--hmark-sport-mask value
A 16 bit source port mask in hexadecimal.
--hmark-dport-mask value
A 16 bit destination port mask in hexadecimal.
--hmark-spi-mask value
A 32 bit field with spi mask.
--hmark-proto-mask value
An 8 bit field with layer 4 protocol number.
--hmark-rnd value
A 32 bit random custom value to feed hash calculation.
Examples:
iptables -t mangle -A PREROUTING -m conntrack --ctstate NEW
-j HMARK --hmark-tuple ct,src,dst,proto --hmark-offset 10000 --hmark-mod 10 --hmark-rnd 0xfeedcafe
iptables -t mangle -A PREROUTING -j HMARK --hmark-offset 10000 --hmark-tuple src,dst,proto --hmark-mod 10
--hmark-rnd 0xdeafbeef
IDLETIMER
This target can be used to identify when interfaces have been idle for a certain period of time. Timers are
identified by labels and are created when a rule is set with a new label. The rules also take a timeout value
(in seconds) as an option. If more than one rule uses the same timer label, the timer will be restarted when‐
ever any of the rules get a hit. One entry for each timer is created in sysfs. This attribute contains the
timer remaining for the timer to expire. The attributes are located under the xt_idletimer class:
/sys/class/xt_idletimer/timers/<label>
When the timer expires, the target module sends a sysfs notification to the userspace, which can then decide
what to do (eg. disconnect to save power).
--timeout amount
This is the time in seconds that will trigger the notification.
--label string
This is a unique identifier for the timer. The maximum length for the label string is 27 characters.
LED
This creates an LED-trigger that can then be attached to system indicator lights, to blink or illuminate them
when certain packets pass through the system. One example might be to light up an LED for a few minutes every
time an SSH connection is made to the local machine. The following options control the trigger behavior:
--led-trigger-id name
This is the name given to the LED trigger. The actual name of the trigger will be prefixed with "net‐
filter-".
--led-delay ms
This indicates how long (in milliseconds) the LED should be left illuminated when a packet arrives
iptables -A INPUT -p tcp --dport 22 -j LED --led-trigger-id ssh
Then attach the new trigger to an LED:
echo netfilter-ssh >/sys/class/leds/ledname/trigger
LOG
Turn on kernel logging of matching packets. When this option is set for a rule, the Linux kernel will print
some information on all matching packets (like most IP/IPv6 header fields) via the kernel log (where it can be
read with dmesg(1) or read in the syslog).
This is a "non-terminating target", i.e. rule traversal continues at the next rule. So if you want to LOG the
packets you refuse, use two separate rules with the same matching criteria, first using target LOG then DROP
(or REJECT).
--log-level level
Level of logging, which can be (system-specific) numeric or a mnemonic. Possible values are (in
decreasing order of priority): emerg, alert, crit, error, warning, notice, info or debug.
--log-prefix prefix
Prefix log messages with the specified prefix; up to 29 letters long, and useful for distinguishing
messages in the logs.
--log-tcp-sequence
Log TCP sequence numbers. This is a security risk if the log is readable by users.
--log-tcp-options
Log options from the TCP packet header.
--log-ip-options
Log options from the IP/IPv6 packet header.
--log-uid
Log the userid of the process which generated the packet.
MARK
This target is used to set the Netfilter mark value associated with the packet. It can, for example, be used
in conjunction with routing based on fwmark (needs iproute2). If you plan on doing so, note that the mark
needs to be set in the PREROUTING chain of the mangle table to affect routing. The mark field is 32 bits
wide.
--set-xmark value[/mask]
Zeroes out the bits given by mask and XORs value into the packet mark ("nfmark"). If mask is omitted,
0xFFFFFFFF is assumed.
--set-mark value[/mask]
Zeroes out the bits given by mask and ORs value into the packet mark. If mask is omitted, 0xFFFFFFFF is
assumed.
The following mnemonics are available:
--and-mark bits
Binary AND the nfmark with bits. (Mnemonic for --set-xmark 0/invbits, where invbits is the binary nega‐
tion of bits.)
anyway).
--to-ports port[-port]
This specifies a range of source ports to use, overriding the default SNAT source port-selection
heuristics (see above). This is only valid if the rule also specifies one of the following protocols:
tcp, udp, dccp or sctp.
--random
Randomize source port mapping If option --random is used then port mapping will be randomized (kernel
>= 2.6.21).
IPv6 support available since Linux kernels >= 3.7.
MIRROR (IPv4-specific)
This is an experimental demonstration target which inverts the source and destination fields in the IP header
and retransmits the packet. It is only valid in the INPUT, FORWARD and PREROUTING chains, and user-defined
chains which are only called from those chains. Note that the outgoing packets are NOT seen by any packet
filtering chains, connection tracking or NAT, to avoid loops and other problems.
NETMAP
This target allows you to statically map a whole network of addresses onto another network of addresses. It
can only be used from rules in the nat table.
--to address[/mask]
Network address to map to. The resulting address will be constructed in the following way: All 'one'
bits in the mask are filled in from the new `address'. All bits that are zero in the mask are filled
in from the original address.
IPv6 support available since Linux kernels >= 3.7.
NFLOG
This target provides logging of matching packets. When this target is set for a rule, the Linux kernel will
pass the packet to the loaded logging backend to log the packet. This is usually used in combination with
nfnetlink_log as logging backend, which will multicast the packet through a netlink socket to the specified
multicast group. One or more userspace processes may subscribe to the group to receive the packets. Like LOG,
this is a non-terminating target, i.e. rule traversal continues at the next rule.
--nflog-group nlgroup
The netlink group (0 - 2^16-1) to which packets are (only applicable for nfnetlink_log). The default
value is 0.
--nflog-prefix prefix
A prefix string to include in the log message, up to 64 characters long, useful for distinguishing mes‐
sages in the logs.
--nflog-range size
The number of bytes to be copied to userspace (only applicable for nfnetlink_log). nfnetlink_log
instances may specify their own range, this option overrides it.
--nflog-threshold size
Number of packets to queue inside the kernel before sending them to userspace (only applicable for
nfnetlink_log). Higher values result in less overhead per packet, but increase delay until the packets
reach userspace. The default value is 1.
useful for multicore systems: start multiple instances of the userspace program on queues x, x+1, ..
x+n and use "--queue-balance x:x+n". Packets belonging to the same connection are put into the same
nfqueue.
--queue-bypass
By default, if no userspace program is listening on an NFQUEUE, then all packets that are to be queued
are dropped. When this option is used, the NFQUEUE rule behaves like ACCEPT instead, and the packet
will move on to the next table.
--queue-cpu-fanout
Available starting Linux kernel 3.10. When used together with --queue-balance this will use the CPU ID
as an index to map packets to the queues. The idea is that you can improve performance if there's a
queue per CPU. This requires --queue-balance to be specified.
NOTRACK
This extension disables connection tracking for all packets matching that rule. It is equivalent with -j CT
--notrack. Like CT, NOTRACK can only be used in the raw table.
RATEEST
The RATEEST target collects statistics, performs rate estimation calculation and saves the results for later
evaluation using the rateest match.
--rateest-name name
Count matched packets into the pool referred to by name, which is freely choosable.
--rateest-interval amount{s|ms|us}
Rate measurement interval, in seconds, milliseconds or microseconds.
--rateest-ewmalog value
Rate measurement averaging time constant.
REDIRECT
This target is only valid in the nat table, in the PREROUTING and OUTPUT chains, and user-defined chains which
are only called from those chains. It redirects the packet to the machine itself by changing the destination
IP to the primary address of the incoming interface (locally-generated packets are mapped to the localhost
address, 127.0.0.1 for IPv4 and ::1 for IPv6).
--to-ports port[-port]
This specifies a destination port or range of ports to use: without this, the destination port is never
altered. This is only valid if the rule also specifies one of the following protocols: tcp, udp, dccp
or sctp.
--random
If option --random is used then port mapping will be randomized (kernel >= 2.6.22).
IPv6 support available starting Linux kernels >= 3.7.
REJECT (IPv6-specific)
This is used to send back an error packet in response to the matched packet: otherwise it is equivalent to
DROP so it is a terminating TARGET, ending rule traversal. This target is only valid in the INPUT, FORWARD
and OUTPUT chains, and user-defined chains which are only called from those chains. The following option con‐
trols the nature of the error packet returned:
--reject-with type
trols the nature of the error packet returned:
--reject-with type
The type given can be icmp-net-unreachable, icmp-host-unreachable, icmp-port-unreachable,
icmp-proto-unreachable, icmp-net-prohibited, icmp-host-prohibited, or icmp-admin-prohibited (*), which
return the appropriate ICMP error message (icmp-port-unreachable is the default). The option tcp-reset
can be used on rules which only match the TCP protocol: this causes a TCP RST packet to be sent back.
This is mainly useful for blocking ident (113/tcp) probes which frequently occur when sending mail to
broken mail hosts (which won't accept your mail otherwise).
(*) Using icmp-admin-prohibited with kernels that do not support it will result in a plain DROP instead of
REJECT
SAME (IPv4-specific)
Similar to SNAT/DNAT depending on chain: it takes a range of addresses (`--to 1.2.3.4-1.2.3.7') and gives a
client the same source-/destination-address for each connection.
N.B.: The DNAT target's --persistent option replaced the SAME target.
--to ipaddr[-ipaddr]
Addresses to map source to. May be specified more than once for multiple ranges.
--nodst
Don't use the destination-ip in the calculations when selecting the new source-ip
--random
Port mapping will be forcibly randomized to avoid attacks based on port prediction (kernel >= 2.6.21).
SECMARK
This is used to set the security mark value associated with the packet for use by security subsystems such as
SELinux. It is valid in the security table (for backwards compatibility with older kernels, it is also valid
in the mangle table). The mark is 32 bits wide.
--selctx security_context
SET
This module adds and/or deletes entries from IP sets which can be defined by ipset(8).
--add-set setname flag[,flag...]
add the address(es)/port(s) of the packet to the set
--del-set setname flag[,flag...]
delete the address(es)/port(s) of the packet from the set
where flag(s) are src and/or dst specifications and there can be no more than six of them.
--timeout value
when adding an entry, the timeout value to use instead of the default one from the set definition
--exist
when adding an entry if it already exists, reset the timeout value to the specified one or to the
default from the set definition
Use of -j SET requires that ipset kernel support is provided, which, for standard kernels, is the case since
512 and 1023 inclusive will be mapped to ports below 1024, and other ports will be mapped to 1024 or
above. Where possible, no port alteration will occur. In Kernels up to 2.6.10, you can add several
--to-source options. For those kernels, if you specify more than one source address, either via an
address range or multiple --to-source options, a simple round-robin (one after another in cycle) takes
place between these addresses. Later Kernels (>= 2.6.11-rc1) don't have the ability to NAT to multiple
ranges anymore.
--random
If option --random is used then port mapping will be randomized (kernel >= 2.6.21).
--persistent
Gives a client the same source-/destination-address for each connection. This supersedes the SAME tar‐
get. Support for persistent mappings is available from 2.6.29-rc2.
Kernels prior to 2.6.36-rc1 don't have the ability to SNAT in the INPUT chain.
IPv6 support available since Linux kernels >= 3.7.
SNPT (IPv6-specific)
Provides stateless source IPv6-to-IPv6 Network Prefix Translation (as described by RFC 6296).
You have to use this target in the mangle table, not in the nat table. It takes the following options:
--src-pfx [prefix/length]
Set source prefix that you want to translate and length
--dst-pfx [prefix/length]
Set destination prefix that you want to use in the translation and length
You have to use the DNPT target to undo the translation. Example:
ip6tables -t mangle -I POSTROUTING -s fd00::/64 -o vboxnet0 -j SNPT --src-pfx fd00::/64 --dst-pfx
2001:e20:2000:40f::/64
ip6tables -t mangle -I PREROUTING -i wlan0 -d 2001:e20:2000:40f::/64 -j DNPT --src-pfx
2001:e20:2000:40f::/64 --dst-pfx fd00::/64
You may need to enable IPv6 neighbor proxy:
sysctl -w net.ipv6.conf.all.proxy_ndp=1
You also have to use the NOTRACK target to disable connection tracking for translated flows.
TCPMSS
This target allows to alter the MSS value of TCP SYN packets, to control the maximum size for that connection
(usually limiting it to your outgoing interface's MTU minus 40 for IPv4 or 60 for IPv6, respectively). Of
course, it can only be used in conjunction with -p tcp.
This target is used to overcome criminally braindead ISPs or servers which block "ICMP Fragmentation Needed"
or "ICMPv6 Packet Too Big" packets. The symptoms of this problem are that everything works fine from your
Linux firewall/router, but machines behind it can never exchange large packets:
1. Web browsers connect, then hang with no data received.
MSS.
--clamp-mss-to-pmtu
Automatically clamp MSS value to (path_MTU - 40 for IPv4; -60 for IPv6). This may not function as
desired where asymmetric routes with differing path MTU exist — the kernel uses the path MTU which it
would use to send packets from itself to the source and destination IP addresses. Prior to Linux
2.6.25, only the path MTU to the destination IP address was considered by this option; subsequent ker‐
nels also consider the path MTU to the source IP address.
These options are mutually exclusive.
TCPOPTSTRIP
This target will strip TCP options off a TCP packet. (It will actually replace them by NO-OPs.) As such, you
will need to add the -p tcp parameters.
--strip-options option[,option...]
Strip the given option(s). The options may be specified by TCP option number or by symbolic name. The
list of recognized options can be obtained by calling iptables with -j TCPOPTSTRIP -h.
TEE
The TEE target will clone a packet and redirect this clone to another machine on the local network segment. In
other words, the nexthop must be the target, or you will have to configure the nexthop to forward it further
if so desired.
--gateway ipaddr
Send the cloned packet to the host reachable at the given IP address. Use of 0.0.0.0 (for IPv4 pack‐
ets) or :: (IPv6) is invalid.
To forward all incoming traffic on eth0 to an Network Layer logging box:
-t mangle -A PREROUTING -i eth0 -j TEE --gateway 2001:db8::1
TOS
This module sets the Type of Service field in the IPv4 header (including the "precedence" bits) or the Prior‐
ity field in the IPv6 header. Note that TOS shares the same bits as DSCP and ECN. The TOS target is only valid
in the mangle table.
--set-tos value[/mask]
Zeroes out the bits given by mask (see NOTE below) and XORs value into the TOS/Priority field. If mask
is omitted, 0xFF is assumed.
--set-tos symbol
You can specify a symbolic name when using the TOS target for IPv4. It implies a mask of 0xFF (see NOTE
below). The list of recognized TOS names can be obtained by calling iptables with -j TOS -h.
The following mnemonics are available:
--and-tos bits
Binary AND the TOS value with bits. (Mnemonic for --set-tos 0/invbits, where invbits is the binary
negation of bits. See NOTE below.)
--or-tos bits
Binary OR the TOS value with bits. (Mnemonic for --set-tos bits/bits. See NOTE below.)
way. It can also change the mark value which can then be used in advanced routing rules. It takes three
options:
--on-port port
This specifies a destination port to use. It is a required option, 0 means the new destination port is
the same as the original. This is only valid if the rule also specifies -p tcp or -p udp.
--on-ip address
This specifies a destination address to use. By default the address is the IP address of the incoming
interface. This is only valid if the rule also specifies -p tcp or -p udp.
--tproxy-mark value[/mask]
Marks packets with the given value/mask. The fwmark value set here can be used by advanced routing.
(Required for transparent proxying to work: otherwise these packets will get forwarded, which is proba‐
bly not what you want.)
TRACE
This target marks packets so that the kernel will log every rule which match the packets as those traverse the
tables, chains, rules.
A logging backend, such as nf_log_ipv4(6) or nfnetlink_log, must be loaded for this to be visible. The pack‐
ets are logged with the string prefix: "TRACE: tablename:chainname:type:rulenum " where type can be "rule" for
plain rule, "return" for implicit rule at the end of a user defined chain and "policy" for the policy of the
built in chains.
It can only be used in the raw table.
TTL (IPv4-specific)
This is used to modify the IPv4 TTL header field. The TTL field determines how many hops (routers) a packet
can traverse until it's time to live is exceeded.
Setting or incrementing the TTL field can potentially be very dangerous, so it should be avoided at any cost.
This target is only valid in mangle table.
Don't ever set or increment the value on packets that leave your local network!
--ttl-set value
Set the TTL value to `value'.
--ttl-dec value
Decrement the TTL value `value' times.
--ttl-inc value
Increment the TTL value `value' times.
ULOG (IPv4-specific)
This is the deprecated ipv4-only predecessor of the NFLOG target. It provides userspace logging of matching
packets. When this target is set for a rule, the Linux kernel will multicast this packet through a netlink
socket. One or more userspace processes may then subscribe to various multicast groups and receive the pack‐
ets. Like LOG, this is a "non-terminating target", i.e. rule traversal continues at the next rule.
--ulog-nlgroup nlgroup
This specifies the netlink group (1-32) to which the packet is sent. Default value is 1.
--ulog-prefix prefix
iptables 1.4.21 iptables-extensions(8)
Back to main site | Back to man page index